Recent content by condac

I have 3 WD15EADS-00P8B0 drives in my software raid5 in linux, and i have had performance issue since i bought them over 1 year ago, and i recently figured out that it is a problem with this model. They get hickups all the time. i haven't found any solution to the problem yet and i will have to...

i think you missed my previus post, i was diving into the thread with some questions of my own, i should have created a new one perhaps..

Will a Zalman "ZM-GWB8800 GTS" fit on a GT card?

none of the ASUS P5K boards have 3 USABLE pci slots the ones that have 3pci have the pci just under the pcie and the graphic cooler is blocking that slot then...

Was going to start a new thread but i'm puting my question in here because the topic is the same. hope you don't mind. I'm looking for a mobo to go with a Q6600 and DDR2 that I'm about to buy. I'm looking a good OC and a fanless motherboard. And the most important I must have 3PCI slots that...

ok, thx! A Core 2 duo is on the way now....

Hi I'm planing on getting a core2 duo cpu and is wondering witch cpu block have the best cooling performance in a 5-7 l/h flow system. The ones i can get my hand on is the following: WaterChill DYO - CPU Cooler (LGA775) Alphacool NexXxos XP Light, Intel775 Zalman WB4 GOLD CPU and some...

The Black ice pro is not very air restrictive so any fans will do just fine. But it depend on how cold you want your water to be and how much heat your systems produce. But for silent setups it is one of the best for low flow fans. But the noize vs. air flow is not very good on that fan i...

I have been looking for a ram drive for several months now. And I can't find a good working one. I want the folowing options in the program: 1. Up to 2GB size 2. Mounted and already formated on startup. Optional: 3. Resize without reboot. Or remove without reboot (to get the ram back to...

-offtopic - ignore if you want - I didn't mean to be rude or anything, I don't know if this forum is an international forum or anything, but the thing is that the metric system is the most used around the world, and I'm glad that i have it. I just feel sorry for you all that have to calculate...

I can give you some tips before you buy. Messure twice, buy once. I messured wrong and had some hard time fitting the rad where I planed in the begining. And Messure twice, cut once. For the tubing, the big fat tubes look nice but they have no effect if you have a small opening some where...

They will disapear after a while, and if they don't they often don't do any harm if they are just sitting there. The only bad about bubbles is if they are circulating in the system then they can harm the pump if its long runtime with bubbles. 3/16" tubing that is the smallest I have heard of...

The reason i thought mounting a rad at the bottom is bad is if i blow in air my small 80mm fans cant blow out all air. And the diffrent to have it at the bottom or front is no diffrent at all. My self i have it on the bottom and the air is not blow in or out, its blown around, I havn't cut the...

It is all very strange. But 47C is a lot cooler than 57C and all that by refitting and playing around. Are you messuring at full load on the cpu? beacause that is the best way to messure and get the same results. The temp can diff up to 20C between load and idle. So you should allways messure at...

Can you stick to one type of messure method please, all this mix make you confused. You messure the room i F and your cpu in C, can you messure the room in C too it will be nice. And you can calculate the temps easy. If you have 23C in your room and 40C on your cpu. And the room rise by 5...